Meraki MR Setup for Yelp Wi-Fi

This guide will walk you through the process of creating a Meraki Network configured to support Yelp WiFi. Once you have a Network created, you will be able to add access points and begin using them to create your Yelp WiFi hotspots.

Instructions on how to configure:

Location and scanning

  1. Open your Meraki dashboard at meraki.cisco.com
  2. In the left navigation panel, go to Network-wide, then click General
  3. Scroll down to Traffic Analysis and select Traffic analysis enabled from the dropdown menu

Traffic Analysis

  1. Scroll to Location and scanning and configure it as follows:
  • Analytics: Analytics enabled
  • Scanning API: Scanning API enabled
  • Validator: Send your validator to your Yelp WiFi representative, they will use this to generate your Post URL and Secret needed below.

Location and scanning

  1. Add a Post URL
  • Post URL: http://checkin.getturnstyle.com/ (from your Yelp WiFi representative)
  • Secret: From your Yelp WiFi representative
  • API Version: 2.0
  1. Click Validate. If successful, a confirmation message will appear. If unsuccessful, please contact your Yelp WiFi representative to verify your Post URL and Secret.

Post URLs

  1. Make sure to Save your changes before navigating to the next section
Please note that data collection will begin within 24 hours.

(Top of Page)

Captive Portal / Access Control

  1. Navigate to Wireless > Access Control
  2. Under Network Access, set Association Requirements: Open (no encryption)
  3. Set Splash page: Sign-on with my RADIUS server

Network Access

  1. Scroll down the page to RADIUS for Splash Page, click Add a server and configure the following:
  • Host 1: 52.22.120.222
  • Host 2: 52.20.198.151
  • Port (1&2): 1812
  • Secret (1&2)From your Yelp WiFi representative
  • Click Test to confirm (username and password are both “test”)

RADIUS

  1. Scroll down to Captive Portal Strength and select Block all access until sign-on is complete from the dropdown menu
  2. For Walled Garden, select Walled garden is enabled
  3. For Walled Garden Ranges, please enter the following domains:
  • *.yelpwifi.com
  • *.getturnstyle.com
  • *.facebook.com
  • *.fbcdn.net
  • connect.facebook.net
  • *.linkedin.com
  • *.licdn.com
  • *.twitter.com
  • *.twimg.com
  • *.bootstrapcdn.com
  • s3.amazonaws.com
  • *.newrelic.com
  • *.akamaihd.net
  • *.nr-data.net

Walled garden

Please note that you may receive an error at this stage indicating that only IP ranges are accepted. If this is the case, please contact Meraki and request for “domain based Walled Garden to be enabled”.
  1. Make sure to Save your changes before navigating to the next section

(Top of Page)

Splash Page

  1. Navigate to Wireless > Splash Page
  2. Select the SSID you set up for your Yelp WiFi configuration from the dropdown menu at the top
  3. Under Custom Splash URL, select the first radio button and enter http://wifi.getturnstyle.com in the field

custom splash url

  1. Scroll down to the Splash Behavior section and select The URL they were trying to fetch

Splash behavior

  1. Save your changes
After completing these steps, your Meraki dashboard should now be configured to support Yelp WiFi!

(Top of Page)

If you’re having trouble with the configuration, please contact [email protected] for support.

 

Meraki MX / Z1 Setup for Yelp Wi-Fi

This guide will walk you through the process of creating a Meraki Network configured to support Yelp WiFi. Once you have a Network created, you will be able to add access points and begin using them to create your Yelp WiFi hotspots.
 

Instructions on how to configure:

Location and scanning

  1. Open your Meraki dashboard at meraki.cisco.com
  2. In the left navigation panel, go to Network-wide, then click General
  3. Scroll down to Traffic Analysis and select Traffic analysis enabled from the dropdown menu
  4. Scroll to Location and scanning and configure it as follows:
  • Analytics: Analytics enabled
  • Scanning API: Scanning API enabled
  • Validator: Send your validator to your Yelp WiFi representative, they will use this to generate your Post URL and Secret needed below.
  1. Add a Post URL:
  • Post URL: From your Yelp WiFi representative
  • Secret: From your Yelp WiFi representative
  • API Version: 2.0
  1. Click Validate. A confirmation message should appear.
  2. Make sure to Save your changes before navigating to the next section. Please note that data collection will begin within 24 hours.

(Top of Page)

Addressing & SSIDs

  1. Navigate to Teleworker Gateway Addressing & VLANs
  2. Under Network wide, select the following options:
  • Network Address Translation (NAT)
  • Track clients by MAC address

Addressing & Vlans

  1. Under Routing, make sure VLANs are Enabled. Then, set up two VLANs as follows:
VLAN 20
  • Name: Default
  • Subnet: 192.168.128.0/24
  • MX IP: 192.168.128.1
  • VLAN ID: 20
  • Group Policy: None
VLAN 10
  • Name: Local Lan
  • Subnet: 192.168.129.0/24
  • MX IP: 192.168.129.1
  • VLAN ID: 10
  • Group Policy: None

Routing

This is not required, but in case you would like to make any ports available for other hardware:
  • Select the ports you’d like to make available
  • Click Edit
  • Assign to VLAN 10

Configure MX Lan ports

  1. Make sure to Save your changes before navigating to the next section
  2. Navigate to Teleworker Gateway > Wireless Settings
  3. Set SSID 1 as follows:
  • Status: enabled
  • Name: Enter an appropriate SSID name, i.e. “BusinessName Guest WiFi”
  • VLAN assignment (for guest Yelp WiFi) is set to: Default (20)
  • Security: open
  • Visibility is set to Advertise this SSID Publicly
To enable a second staff SSID:
  • Status: enabled
  • Name: Enter a SSID name
  • VLAN assignment (for staff wifi) is set to: 10
  • Security: WPA2 PSK
  • WPA Key: Enter the wifi password you’d like to use
  1. Save changes

Wireless Settings

(Top of Page)

Captive Portal / Access Control

  1. Navigate to  Teleworker Gateway > Access Control
  2. Select VLAN: Default (20)
  3. Under Splash page, select the option Sign-on with: my RADIUS server.
  4. Below in the section RADIUS for splash page, click Add a server and configure the following:
  • Host 1: 52.22.120.222
  • Host 2: 52.20.198.151
  • Port (1&2): 1812
  • Secret (1&2)From your Yelp WiFi representative

RADIUS setup

  1. For Walled Garden, select Walled garden is enabled
  2. For Walled Garden Ranges, please enter the following domains:
  • *.yelpwifi.com
  • *.getturnstyle.com
  • *.facebook.com
  • *.fbcdn.net
  • connect.facebook.net
  • *.linkedin.com
  • *.licdn.com
  • *.twitter.com
  • *.twimg.com
  • *.bootstrapcdn.com
  • s3.amazonaws.com
  • *.newrelic.com
  • *.akamaihd.net
  • *.nr-data.net
Please note that you may receive an error at this stage indicating that only IP ranges are accepted. If this is the case, please contact Meraki and request for “domain based Walled Garden to be enabled”.
  1. Set the Controller disconnection behavior to restricted

Controller disconnection behavior

  1. Scroll back to the top of the page and under Access Control, choose Local LAN (10) from the Select VLAN dropdown menu
  2. Under Splash page, select None

Access Control

  1. Save your changes

(Top of Page)

Splash Page

  1. Navigate to Teleworker Gateway > Splash Page
  2. In the section Custom splash URL, select: Or provide a URL where users will be redirected: and enter http://wifi.getturnstyle.com

Custom Splash URL

  1. Scroll down to the Splash Behavior section and select The URL they were trying to fetch
  2. Save your changes
After completing these steps, your Meraki dashboard should now be configured to support Yelp WiFi!

(Top of Page)

If you’re having trouble with the configuration, please contact [email protected] for support.